Skip to main content

Printer Manager D3.18.1 Printer Setting - Print Tab (40 - 78)

Summary

Printer Manager D3.18.1 Printer Setting with SDO Notes - Print Tab (40 - 78)


DESCRIPTION DEFAULT SDO Notes
40) FPowerCalibration 0 Modify the intensity of printing for the F ribbon panel: Increase this setting to increase the power used to print the fluorescent ribbon panel, which makes printed fluorescent thicker or more uniform. Decrease to prevent ribbon breaks while printing fluorescent.
41) FPowerDuplex 0 Customer setting. Modify the intensity of printing for the backside F ribbon panel: Increase to make printed fluorescent thicker or more uniform, decrease to prevent ribbon breaks while printing fluorescent.
42) HalfPanelStartOffset 0 Minimum distance from leading edge of card where half-panel color printing will start. Zero will begin printing as soon as color is detected.
43) KCustom1Power 0 Customer setting to increase or decrease print intensity for K Custom1 panel. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
44) KCustom1Power1200DPI 0 Customer setting to increase or decrease print intensity of 1200 DPI for K Custom1 panel. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
45) KCustom1Power600DPI 0 Customer setting to increase or decrease print intensity for 600 DPI K Custom1 panel. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
46) KFineText Enabled Use a monochrome sharpening algorithm that works better with fine text such as 3 point fonts.
47) KPower 0 Customer setting to increase or decrease print intensity for K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
48) KPower1200DPI 0 Customer setting to increase or decrease print intensity of 1200 DPI for K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
49) KPower600DPI 0 Customer setting to increase or decrease print intensity for 600 DPI K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
50) KPowerCalibration 0 Change intensity of printing for the K ribbon or panel. Increase the power used to print the K panel, which makes single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks while printing the K panel.
51) KPowerCalibration1200DPI 0 Change intensity of 1200 DPI printing for the K ribbon or panel. Increase the power used to print the K panel, which makes single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks while printing the K panel.
52) KPowerCalibration600DPI 0 Change intensity of 600 DPI printing for the K ribbon or panel. Increase the power used to print the K panel, which makes single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks while printing the K panel.
53) KPowerDuplex 0 Customer setting to increase or decrease print intensity for backside K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
54) KWhiteShade 0 Power applied to the print head to reduce ribbon friction without transferring material.
55) LeadTrim 0.254 Number of millimeters (1mm is 0.0394 inch) to remove from the leading edge of a full-size image to keep it within the print area. 1 mm equals about 11.8 dot rows.
56) PowerCalibrationK98mmOffset -20 Offset power added to standard K power calibration for the 98mm ribbons to get consistent density.
57) PowerCalibrationK98mmOffset1200 -5 Offset power added to standard K power calibration for the 98mm ribbons to get consistent density (1200dpi).
58) PowerCalibrationK98mmOffset600 -10 Offset power added to standard K power calibration for the 98mm ribbons to get consistent density (600dpi).
59) PowerCalibrationT98mmOffset 5 Offset power added to standard T power calibration for the 98mm ribbons to get consistent density.
60) PowerCalibrationYMC98mmOffset -15 Offset power added to standard YMC power calibration for the 98mm ribbons to get consistent density.
61) PowerCalibrationYMC98mmOffset600 -8 Offset power added to standard YMC power calibration for the 98mm ribbons to get consistent density (600dpi).
62) RibbonOffset 20.32 Distance in millimeters (1mm is 0.0394 inch) to move the ribbon after the Index Sensor event to start printing.
63) RibbonStripOffset 10 Distance in millimeters (1mm is 0.0394 inch) that the transport motor will move the card, in addition to the image length, to strip the ribbon from the card. Increase this value if ribbon sticks to the trailing edge of the card.
64) SettingsGroupPurpose Print Describe the purpose of the settings group. Group names are not changeable, so use SettingsGroupPurpose to state the reason for creating the settings group. There are no other options.
65) TPower 0 Customer setting. Modify the intensity of printing for the T ribbon panel: Increase to make printed topcoat thicker or more uniform, decrease to prevent ribbon breaks while printing topcoat.
66) TPowerCalibration 0 Modify the intensity of printing for the T ribbon panel: Increase this setting to increase the power used to print the topcoat ribbon panel, which makes printed topcoat thicker or more uniform. Decrease to prevent ribbon breaks while printing topcoat.
67) TPowerDuplex 0 Customer setting. Modify the intensity of printing for the backside T ribbon panel: Increase to make printed topcoat thicker or more uniform, decrease to prevent ribbon breaks while printing topcoat.
68) TrailTrim 1.47 Number of millimeters (1mm is 0.0394 inch) to remove from the trailing edge of a full-size image to keep it within the print area. 1 mm equals about 11.8 dot rows. Mine is set to 1.2 - PRB
69) TWhiteShade 0 Power applied to the print head to reduce ribbon friction without transferring material. Reduce this value if material transfers to the card and it should not.
70) VerticalOffset 17 Aligns printing with the long edges of the card. Number of printhead dots to shift printing toward the top or left side of the card. You cannot change the number of dots between the long edges of the card. Moves image up or down in landscape
71) YMCMinShade 0 The minimum shade value at which YMC color begins to transfer from the ribbon to the card. If a white shirt in a photo does not print, increase this value. If highlights are washed out (gray), decrease this value.
72) YMCPower 0 Customer setting. Modify the intensity of printing for the Y, M, and C ribbon panels: Increase to make color printing more intense. Decrease to reduce intensity or to prevent ribbon breaks while printing colors.
73) YMCPower600 0 Customer setting. Modify the intensity of printing for the 600 DPI Y, M, and C ribbon panels: Increase to make color printing more intense. Decrease to reduce intensity or to prevent ribbon breaks while printing colors.
74) YMCPowerCalibration 0 Change intensity of printing for the Y, M, and C ribbon panels. Increase the power used to print the color panels, which makes colors stronger. Decrease to reduce intensity or prevent ribbon breaks while printing color panels.
75) YMCPowerCalibration600 0 Change intensity of printing for the 600 DPI Y, M, and C ribbon panels. Increase the power used to print the color panels, which makes colors stronger. Decrease to reduce intensity or prevent ribbon breaks while printing color panels.
76) YMCPowerDuplex 0 Customer setting. Modify the intensity of printing for the backside Y, M, and C ribbon panels: Increase to make color printing more intense. Decrease to reduce intensity or to prevent ribbon breaks while printing colors.
77) YMCPowerNosRGB -48 Customer setting. Modify the intensity when printing without the sRGB color mode. Decrease if switching away from sRGB causes over dark printing or ribbon wrinkles or tears. Increase if non sRGB printing is too light. Affects printer ONLY if set to anything besides sRGB.
78) YMCWhiteShade 0 Power applied to the print head to reduce ribbon friction without transferring color. Reduce this value if unprinted or white areas of the card have color applied to them.