Hardware Knowledge Base

Start your search by choosing your product and article type:

Technotes
Bulletins
Discontinuation Notices
Error Codes

Printer Manager D3.18.1 Printer Setting - Print Tab (40 - 78)

 
DESCRIPTIONDEFAULTSDO Notes
   
40) FPowerCalibration0Modify the intensity of printing for the F ribbon panel: Increase this setting to increase the power used to print the fluorescent ribbon panel, which makes printed fluorescent thicker or more uniform. Decrease to prevent ribbon breaks while printing fluorescent.
41) FPowerDuplex0Customer setting. Modify the intensity of printing for the backside F ribbon panel: Increase to make printed fluorescent thicker or more uniform, decrease to prevent ribbon breaks while printing fluorescent.
42) HalfPanelStartOffset0Minimum distance from leading edge of card where half-panel color printing will start. Zero will begin printing as soon as color is detected.
43) KCustom1Power0Customer setting to increase or decrease print intensity for K Custom1 panel. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
44) KCustom1Power1200DPI0Customer setting to increase or decrease print intensity of 1200 DPI for K Custom1 panel. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
45) KCustom1Power600DPI0Customer setting to increase or decrease print intensity for 600 DPI K Custom1 panel. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
46) KFineTextEnabledUse a monochrome sharpening algorithm that works better with fine text such as 3 point fonts.
47) KPower0Customer setting to increase or decrease print intensity for K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
48) KPower1200DPI0Customer setting to increase or decrease print intensity of 1200 DPI for K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
49) KPower600DPI0Customer setting to increase or decrease print intensity for 600 DPI K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
50) KPowerCalibration0Change intensity of printing for the K ribbon or panel. Increase the power used to print the K panel, which makes single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks while printing the K panel.
51) KPowerCalibration1200DPI0Change intensity of 1200 DPI printing for the K ribbon or panel. Increase the power used to print the K panel, which makes single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks while printing the K panel.
52) KPowerCalibration600DPI0Change intensity of 600 DPI printing for the K ribbon or panel. Increase the power used to print the K panel, which makes single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks while printing the K panel.
53) KPowerDuplex0Customer setting to increase or decrease print intensity for backside K panel or K ribbon. Increase to make single-color printing thicker. Decrease for crisp bar codes or if the ribbon breaks when printing the K panel.
54) KWhiteShade0Power applied to the print head to reduce ribbon friction without transferring material.
55) LeadTrim0.254Number of millimeters (1mm is 0.0394 inch) to remove from the leading edge of a full-size image to keep it within the print area. 1 mm equals about 11.8 dot rows.
56) PowerCalibrationK98mmOffset-20Offset power added to standard K power calibration for the 98mm ribbons to get consistent density.
57) PowerCalibrationK98mmOffset1200-5Offset power added to standard K power calibration for the 98mm ribbons to get consistent density (1200dpi).
58) PowerCalibrationK98mmOffset600-10Offset power added to standard K power calibration for the 98mm ribbons to get consistent density (600dpi).
59) PowerCalibrationT98mmOffset5Offset power added to standard T power calibration for the 98mm ribbons to get consistent density.
60) PowerCalibrationYMC98mmOffset-15Offset power added to standard YMC power calibration for the 98mm ribbons to get consistent density.
61) PowerCalibrationYMC98mmOffset600-8Offset power added to standard YMC power calibration for the 98mm ribbons to get consistent density (600dpi).
62) RibbonOffset20.32Distance in millimeters (1mm is 0.0394 inch) to move the ribbon after the Index Sensor event to start printing.
63) RibbonStripOffset10Distance in millimeters (1mm is 0.0394 inch) that the transport motor will move the card, in addition to the image length, to strip the ribbon from the card. Increase this value if ribbon sticks to the trailing edge of the card.
64) SettingsGroupPurposePrintDescribe the purpose of the settings group. Group names are not changeable, so use SettingsGroupPurpose to state the reason for creating the settings group. There are no other options.
65) TPower0Customer setting. Modify the intensity of printing for the T ribbon panel: Increase to make printed topcoat thicker or more uniform, decrease to prevent ribbon breaks while printing topcoat.
66) TPowerCalibration0Modify the intensity of printing for the T ribbon panel: Increase this setting to increase the power used to print the topcoat ribbon panel, which makes printed topcoat thicker or more uniform. Decrease to prevent ribbon breaks while printing topcoat.
67) TPowerDuplex0Customer setting. Modify the intensity of printing for the backside T ribbon panel: Increase to make printed topcoat thicker or more uniform, decrease to prevent ribbon breaks while printing topcoat.
68) TrailTrim1.47Number of millimeters (1mm is 0.0394 inch) to remove from the trailing edge of a full-size image to keep it within the print area. 1 mm equals about 11.8 dot rows. Mine is set to 1.2 - PRB
69) TWhiteShade0Power applied to the print head to reduce ribbon friction without transferring material. Reduce this value if material transfers to the card and it should not.
70) VerticalOffset17Aligns printing with the long edges of the card. Number of printhead dots to shift printing toward the top or left side of the card. You cannot change the number of dots between the long edges of the card. Moves image up or down in landscape
71) YMCMinShade0The minimum shade value at which YMC color begins to transfer from the ribbon to the card. If a white shirt in a photo does not print, increase this value. If highlights are washed out (gray), decrease this value.
72) YMCPower0Customer setting. Modify the intensity of printing for the Y, M, and C ribbon panels: Increase to make color printing more intense. Decrease to reduce intensity or to prevent ribbon breaks while printing colors.
73) YMCPower6000Customer setting. Modify the intensity of printing for the 600 DPI Y, M, and C ribbon panels: Increase to make color printing more intense. Decrease to reduce intensity or to prevent ribbon breaks while printing colors.
74) YMCPowerCalibration0Change intensity of printing for the Y, M, and C ribbon panels. Increase the power used to print the color panels, which makes colors stronger. Decrease to reduce intensity or prevent ribbon breaks while printing color panels.
75) YMCPowerCalibration6000Change intensity of printing for the 600 DPI Y, M, and C ribbon panels. Increase the power used to print the color panels, which makes colors stronger. Decrease to reduce intensity or prevent ribbon breaks while printing color panels.
76) YMCPowerDuplex0Customer setting. Modify the intensity of printing for the backside Y, M, and C ribbon panels: Increase to make color printing more intense. Decrease to reduce intensity or to prevent ribbon breaks while printing colors.
77) YMCPowerNosRGB-48Customer setting. Modify the intensity when printing without the sRGB color mode. Decrease if switching away from sRGB causes over dark printing or ribbon wrinkles or tears. Increase if non sRGB printing is too light. Affects printer ONLY if set to anything besides sRGB.
78) YMCWhiteShade0Power applied to the print head to reduce ribbon friction without transferring color. Reduce this value if unprinted or white areas of the card have color applied to them.
*
×

👋 Hello, if you have any
questions, I'm ready to chat.

Chat Now